How To Cut Vinyl Siding For Ledger Board

August 14, 2021 Post a Comment

Start by making an outline on the siding where you want to position the ledger board. This is used to determine the depth of the notch.

Pin On Diy House Projects

Installing Deck Ledger on Vinyl Siding.

How to cut vinyl siding for ledger board. Measure carefully to cut around the door. You may need to cut notches for obstacles and you may need to pull out nails in order to slip the piece up far enough. Wood or concrete siding will have to.

Aluminum and vinyl siding can easily be removed with tin snips from an area one foot surrounding the ledger board location. Slide the flashing underneath the siding 1 inch. How do you attach a ledger board to a house with vinyl siding.

Place the piece of siding horizontally under the bottom edge of the window. Cut Siding and Flash. Step 2 - Cut Away the Vinyl Siding.

Aluminum and vinyl siding can easily be removed with tin snips from an area one foot surrounding the ledger board location. You want to avoid cutting up the house wrap beneath if possible. Slip the bottom piece of siding under the next-to-bottom piece.

Then slip flashing behind the siding covering the top edge of the ledger. Bend flashing with a block and framing square for a 90 degree bend to fit inside the house corner wall. What is the preferred method when attaching to a house with Vinyl siding.

Infiltrating rainwater can travel downward sideways and even upward so special flashings must be used. Step 3 - Add 2 x 8 Planks Between Joists. Touch device users explore by touch or with swipe gestures.

Make the outline large enough to include space for the deck boards on top the ledger and any trim boards on the sides. After cutting the siding with a circular saw install the flashing. Cut along the line you drew using the circular saw.

Score with a utility knife. Measure the distance from the undersill trim to the locking tab of the siding below. Measure the length and width of your deck to attach the ledger correctly.

Set the blade depth so you wont cut into the house sheathing below the siding. Cut the flashing with tin snips. Watch the blade carefully as youre cutting to make sure its staying on the line.

Installing Deck Ledger on Vinyl Siding - YouTube. Since you will be removing the vinyl anyway so you can get the ledgers properly flashed and detailed you can just cut it with a pair of snips. When autocomplete results are available use up and down arrows to review and enter to select.

Cut a length of metal drip cap flashing to the same length as the Z flashing. Install the ledger overtop of the siding or remove the siding attach the ledger and recase around it. Slip flashing under siding Snap a chalk line cut out the siding and tack up the ledger board.

Apr 27 2015 - attaching a deck ledger board to a vinyl-sided house requires a few extra trim pieces to keep water from leaking behind the siding. Drip caps direct water away from the house keeping it from getting behind the ledger board. A tool like this helps a lot in removal and replacement of vinyl siding in the middle of a wall.

Slip the flashing under. Use your free hand to hold the vinyl siding down so it doesnt shift while youre cutting it. You can then trim the pieces to be reinstalled with a J channel after the deck is completed for a clean finished look.

Mark the siding to be cut. Overlap flashing by 3 inches and cut it for the doorway. Click to see full answer.

Use a nail as a temporary place holder to check. Locate the rim joist and mark an outline on the siding where you want to position the ledger board using a tape measure. Once you are sure about the joist location mark out the cutaway areas outer shape using a soft pencil or marker and a straight edge.

Push the saw along the line at a steady rate to get a clean smooth cut. Carefully cut away the siding with a utility knife braced along the edge of the carpenters square to avoid slicing through the house wrap. If playback doesnt begin.

At this point you can also caulk the inside corner of the ledger. Set the bottom of the ledger at the on a chalk line set at the level you predetermined before you cut the siding. Snap a chalk line cut out the siding and tack up the ledger board.

First ensure your circular saw is equal to the thickness of the deck then cut the ledger outline. Mark it at inch past the edge of each side of the window. How do I attach a ledger board to a house with vinyl siding.

Use a sharp razor knife and a straight edge as a guide to score cut the vinyl and after several passes gradually cut through. Cut away the marked area of siding with tin snips. Start by making an outline on the siding where you want to position the ledger board.

Set a ledger at the top of the rafter section as well to control rotation of the new section. Then slip flashing behind the siding covering the top edge of the ledger. If you cut out your siding to install a ledger board careful steps must be taken to ensure that moisture cannot reach your house.

How To Replace Deck Ledger Building A Deck Diy Deck Deck Design

Pin On Outdoor Living

Attaching Ledger Board Deck With Pergola Pergola Pergola Kits

Best Way To Flash A Ledger Board Deck Ledger Boards Are A Common Source Of Water Infiltration And It Can Be Years Befor Modern Deck Building A Deck Diy Deck